Head:	Program_Generator configuration file	V1.0
Sheet:	DCC	Weichenstepper1
Line:	-	Allgemeine Definitionen - Arduino												
Line:	Act	Heartb0				Heartbeat Channel 0			RGB_Heartbeat2(#LED, 0, 5)	0	1	0	0	0
Line:	-	Portdef.				Pins LED Bus definieren			// Set_LED_OutpPinLst(6 A4 2)			0	0	
Line:	Act	Portdef.				Pins LED Bus definieren			// Set_LED_OutpPinLst(27 32 16 14 18 19 23 0)			0	0	
Line:	-	Allg				Sicherung des letzten Zustandes			#define ENABLE_STORE_STATUS()			0	0	
Line:	-	Allg				Debug-Funktion			#define COMMANDS_DEBUG			0	0	
Line:	-													
Line:	Act	Allg	SwitchD1			LED zum Platinentaster			Mainboard_LED(1, #InCh)			1	0	
Line:	Act	Allg	SwitchD2			LED zum Platinentaster			Mainboard_LED(2, #InCh)			1	0	
Line:	Act	Allg	SwitchD3			LED zum Platinentaster			Mainboard_LED(3, #InCh)			1	0	
Line:	-													
Line:	Act	W0 	900	Rot		Verbindung DCC und Taster      W0	V1	S1	Logic(Weiche0, #InCh OR SwitchD1)			1	0	
Line:	Act	W0 	Weiche0			Taster links	V1	S1	T_FlipFlopReset(Weiche0L, #InCh, SI_0)			1	0	
Line:	Act	W0 	Weiche0L			Weichenstepper Weiche 1	V1	S1	// Activation: Binary{NewLine}Bin_InCh_to_TmpVar(#InCh, 1){NewLine}PatternT4(#LED,28,SI_LocalVar,2,0,255,0,PM_SEQUENZ_NO_RESTART,4 Sec,100 ms,4 Sec,100 ms,127,255,0,0,127,0,0,0  ,0,63,128,63)	1	C1-2	1	0	0
Line:	-						 							
Line:	Act	W1	901	Rot		Verbindung DCC und Taster      W1	V1	S1	Logic(Weiche1, #InCh OR SwitchD2)			1	0	
Line:	Act	W1	Weiche1 			Taster mitte	V1	S1	T_FlipFlopReset(Weiche1M, #InCh, SI_0)			1	0	
Line:	Act	W1	Weiche1M			Weichenstepper Weiche 2	V1	S1	// Activation: Binary{NewLine}Bin_InCh_to_TmpVar(#InCh, 1){NewLine}PatternT4(#LED,28,SI_LocalVar,2,0,255,0,PM_SEQUENZ_NO_RESTART,4 Sec,100 ms,4 Sec,100 ms,127,255,0,0,127,0,0,0  ,0,63,128,63)	2	C1-2	1	0	0
Line:	-						 							
Line:	Act	W2 	902	Rot		Verbindung DCC und Taster      W2	V1	S1	Logic(Weiche2, #InCh OR SwitchD3)			1	0	
Line:	Act	W2 	Weiche2 			Taster rechts	V1	S1	T_FlipFlopReset(Weiche2R, #InCh, SI_0)			1	0	
Line:	Act	W2 	Weiche2R			Weichenstepper Weiche 3	V1	S1	// Activation: Binary{NewLine}Bin_InCh_to_TmpVar(#InCh, 1){NewLine}PatternT4(#LED,28,SI_LocalVar,2,0,255,0,PM_SEQUENZ_NO_RESTART,4 Sec,100 ms,4 Sec,100 ms,127,255,0,0,127,0,0,0  ,0,63,128,63)	3	C1-2	1	0	0
Line:	-						 							
Line:	Act	W0 	Weiche0			Taster Links	V1	S1	T_FlipFlop2Reset(Relais0R, Relais0G, #InCh, SI_0)			1	0	
Line:	Act	W0 	Relais0R			Herzstückrelais Weiche 1	V1	S1	Herz_BiRelais(#LED, #InCh, C1, 1000 ms)	4	C1-2	2	0	0
Line:	Act	W1	Weiche1 			Taster Mitte	V1	S1	T_FlipFlop2Reset(Relais1R, Relais1G, #InCh, SI_0)			1	0	
Line:	Act	W1	Relais1R			Herzstückrelais Weiche 2	V1	S1	Herz_BiRelais(#LED, #InCh, C3, 1000 ms)	4	C3-4	2	0	0
Line:	Act	W2 	Weiche2 			Taster Rechts	V1	S1	T_FlipFlop2Reset(Relais2R, Relais2G, #InCh, SI_0)			1	0	
Line:	Act	W2 	Relais2R			Herzstückrelais Weiche 3	V1	S1	Herz_BiRelais(#LED, #InCh, C2, 1000 ms)	5	C2-3	2	0	0
Line:	-													
Line:	Act	Allg				Zeigt, dass das Signal zurück kommt			RGB_Heartbeat2(#LED, 5, 10)	6	1	0	0	0
Line:	-