Head:	Program_Generator configuration file	V1.0
Sheet:	DCC	ServoTesterMitTaster (2)
Line:	-													
Line:	Act								#define ENABLE_STORE_STATUS					
Line:	-													
Line:	Act					Zeigt an, dass die LEDs angesteuert werden			RGB_Heartbeat(#LED)	0	1	0	0	
Line:	-													
Line:	Act		SwitchD1		*	Stern erzwingt das "EEPROM"-Speichern			PushButton_0_1(#InCh, Taster_D1_0, 1, 1, 1, 0, 0 Sek)			1	0	
Line:	Act		Taster_D1_0			LokSchuppenTore (pc){NewLine}5 Sekunden Pause zwischen den Türen li und re			// Activation: N_Buttons1{NewLine}InCh_to_TmpVar1(#InCh, 2){NewLine}PatternT7(#LED,28,SI_LocalVar,2,0,255,0,0,1 Sec,5 Sec,6 Sec,10 ms,5 Sec,6 Sec,10 ms,0,0,0,10,10,0,0,0,220,0,0,220,0,0  ,63,128,0,63,128,0,63)	1	C1-2	2	0	0
Line:	-													
Line:	Act		SwitchD2		*	Stern erzwingt das "EEPROM"-Speichern			PushButton_0_1(#InCh, Taster_D2_0, 1, 1, 1, 0, 0 Sek)			1	0	
Line:	Act		Taster_D2_0			LokSchuppenTore (pc)			// Activation: N_Buttons1{NewLine}InCh_to_TmpVar1(#InCh, 2){NewLine}PatternT7(#LED,28,SI_LocalVar,2,0,255,0,0,1 Sec,5 Sec,6 Sec,10 ms,5 Sec,6 Sec,10 ms,0,0,0,10,10,0,0,0,220,0,0,220,0,0  ,63,128,0,63,128,0,63)	2	C1-2	2	0	0
Line:	-													
Line:	Act		SwitchD3		*	Stern erzwingt das "EEPROM"-Speichern			PushButton_0_1(#InCh, Taster_D3_0, 1, 1, 1, 0, 0 Sek)			1	0	
Line:	Act		Taster_D3_0			LokSchuppenTore (pc)			// Activation: N_Buttons1{NewLine}InCh_to_TmpVar1(#InCh, 2){NewLine}PatternT7(#LED,28,SI_LocalVar,2,0,255,0,0,1 Sec,5 Sec,6 Sec,10 ms,5 Sec,6 Sec,10 ms,0,0,0,10,10,0,0,0,220,0,0,220,0,0  ,63,128,0,63,128,0,63)	3	C1-2	2	0	0
Line:	-													
Line:	Act		SwitchD1						Mainboard_LED(1, #InCh)			1	0	
Line:	Act		SwitchD2						Mainboard_LED(2, #InCh)			1	0	
Line:	Act		SwitchD3						Mainboard_LED(3, #InCh)			1	0	
Line:	-													
Line:	-													
Line:	Act								RGB_Heartbeat(#LED)	4	1	0	0	0